View PCA9519_1112407.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PCA9519
4-channel level translating I2C-bus/SMBus repeater
Rev. 01 -- 22 June 2006 Objective data sheet
1. General description
The PCA9519 is a 4-channel level translating I2C-bus/SMBus repeater that enables the processor low voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O. While retaining all the operating modes and features of the I2C-bus system during the level shifts, it also permits extension of the I2C-bus by providing bidirectional buffering for both the data (SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBus maximum capacitance of 400 pF on the higher voltage side. The SDA and SCL pins are over-voltage tolerant and are high-impedance when the PCA9519 is unpowered. The port B drivers are compliant with SMBus I/O levels, while port A uses a current sensing mechanism to detect the input or output LOW signal which prevents bus lock-up. The port A uses a 1 mA current source for pull-up and a 200 pull-down driver. This results in a LOW on port A accommodating smaller voltage swings. The output pull-down on the port A internal buffer LOW is set for approximately 0.2 V, while the input threshold of the internal buffer is set about 50 mV lower than that of the output voltage LOW. When the port A I/O is driven LOW internally, the LOW is not recognized as a LOW by the input. This prevents a lock-up condition from occurring. The output pull-down on the port B drives a hard LOW and the input level is set at 0.3 of SMBus or I2C-bus voltage level which enables port B to connect to any other I2C-bus device or buffer. The PCA9519 drivers are not enabled unless VCC(A) is above 0.8 V and VCC(B) is above 2.5 V. The enable (EN) pin can also be used to turn the drivers on and off under system control. Caution should be observed to only change the state of the EN pin when the bus is idle.
2. Features
I 4-channel (4 SCL/SDA pairs), bidirectional buffer isolates capacitance and allows 400 pF on port B of the device I Voltage level translation from port A (1 V to VCC(B) - 1 V) to port B (3.0 V to 5.5 V) I Requires no external pull-up resistors on lower voltage port A I Active HIGH repeater enable input I Open-drain inputs/outputs I Lock-up free operation I Supports arbitration and clock stretching across the repeater I Accommodates Standard-mode and Fast-mode I2C-bus devices and multiple masters I Powered-off high-impedance I2C-bus pins I Operating supply voltage range of 1.0 V to VCC(B) - 1 V on port A, 3.0 V to 5.5 V on port B I 5 V tolerant B-side SCL and SDA and enable pins
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
I 0 Hz to 400 kHz clock frequency Remark: The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater. I ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 I Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA I Packages offered: TSSOP20, HVQFN24
3. Ordering information
Table 1. Ordering information Package Name TSSOP20 HVQFN24 Description plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm Version SOT616-1 plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1 Type number Topside mark PCA9519PW PCA9519BS PCA9519 9519
4. Functional diagram
VCC(A) VCC(B)
PCA9519
VCC(A)
1 mA
A1 VCC(A)
1 mA
B1
A2
B2
VCC(A)
1 mA
A8
B8
EN
002aab643
GND
Fig 1. Functional diagram of PCA9519
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
2 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
5. Pinning information
5.1 Pinning
23 VCC(A)
22 GND
21 n.c.
24 A1
EN B1 B2 B3 B4 B5 B6 B7 B8
1 2 3 4 5 6 7 8 9
20 VCC(B) 19 A1 18 A2 17 A3 16 A4 15 A5 14 A6 13 A7 12 A8 11 VCC(A)
002aab640
A2 A3 A4 A5 A6 A7
1 2 3 4 5 6 VCC(B) 10 EN 11 B8 12 7 8 9
19 B1 18 B2 17 B3 16 B4 15 B5 14 B6 13 B7
002aab641
terminal 1 index area
PCA9519BS
PCA9519PW
n.c.
GND 10
Transparent top view
Fig 2. Pin configuration for TSSOP20
Fig 3. Pin configuration for HVQFN24
5.2 Pin description
Table 2. Symbol EN GND VCC(A) A1 A2 A3 A4 A5 A6 A7 A8 VCC(B) B8 B7 B6 B5 B4 B3 Pin description Pin TSSOP20 1 10 11 19 18 17 16 15 14 13 12 20 9 8 7 6 5 4 HVQFN24 11 22[1] 23 24 1 2 3 4 5 6 7 10 12 13 14 15 16 17 enable input (active HIGH) ground (0 V) port A power supply A1 port (low voltage side)[2] A2 port (low voltage side)[2] A3 port (low voltage side)[2] A4 port (low voltage side)[2] A5 port (low voltage side)[2] A6 port (low voltage side)[2] A7 port (low voltage side)[2] A8 port (low voltage side)[2] port B power supply B8 port (SMBus/I2C-bus side)[2] B7 port (SMBus/I2C-bus side)[2] B6 port (SMBus/I2C-bus side)[2] B5 port (SMBus/I2C-bus side)[2] B4 port (SMBus/I2C-bus side)[2] B3 port (SMBus/I2C-bus side)[2] Description
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
n.c.
A8
20 n.c.
3 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
Pin description ...continued Pin TSSOP20 HVQFN24 18 19 8, 9, 20, 21 B2 port (SMBus/I2C-bus side)[2] B1 port (SMBus/I2C-bus side)[2] not connected 3 2 Description
Table 2. Symbol B2 B1 n.c.
[1]
HVQFN package die supply ground is connected to both the GND pin and the exposed center pad. The GND pin must be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board-level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad on the board, and for proper heat conduction through the board thermal vias need to be incorporated in the PCB in the thermal pad region. Port A and port B can be used for either SCL or SDA.
[2]
6. Functional description
Refer to Figure 1 "Functional diagram of PCA9519". The PCA9519 enables I2C-bus or SMBus translation down to VCC(A) as low as 1.0 V without degradation of system performance. The PCA9519 contains 8 bidirectional open-drain buffers specifically designed to support up-translation/down-translation between the low voltage and 3.3 V SMBus or 5 V I2C-bus. Port B I/Os are over-voltage tolerant to 5.5 V even when the device is unpowered. The PCA9519 includes a power-up circuit that keeps the output drivers turned off until VCC(B) is above 2.5 V and the VCC(A) is above 0.8 V. VCC(B) and VCC(A) can be applied in any sequence at power-up. After power-up and with the EN pin HIGH, a LOW level on the port A (below approximately 0.15 V) turns the corresponding port B driver (either SDA or SCL) on and drives the port B down to about 0 V. When port A rises above approximately 0.15 V, the port B pull-down driver is turned off and the external pull-up resistor pulls the pin HIGH. When the port B falls first and goes below 0.3VCC(B), the port A driver is turned on and the port A pulls down to 0.2 V (typical). The port B pull-down is not enabled unless the port A voltage goes below VILc. If the port A low voltage goes below VILc, the port B pull-down driver is enabled until the port A rises above approximately 0.15 V (VILc), then the port B, if not externally driven LOW, will continue to rise being pulled up by the external pull-up resistor. Remark: Ground offset between the PCA9519 ground and the ground of devices on port A of the PCA9519 must be avoided. The reason for this cautionary remark is that a CMOS/NMOS open-drain capable of sinking 3 mA of current at 0.4 V will have an output resistance of 133 or less (R = E / I). Such a driver will share enough current with the port A output pull-down of the PCA9519 to be seen as a LOW as long as the ground offset is zero. If the ground offset is greater than 0 V, then the driver resistance must be less. Since VILc can be as low as 90 mV at cold temperatures and the low end of the current distribution, the maximum ground offset should not exceed 50 mV. Bus repeaters that use an output offset are not interoperable with port A of the PCA9519 as their output LOW levels will not be recognized by the PCA9519 as a LOW. If the PCA9519 is placed in an application where the VIL of the port A of the PCA9519 does not
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
4 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
go below its VILc it will pull the port B LOW initially when the port A input transitions LOW but port B will return HIGH, so it will not reproduce the port A input on port B. Such applications should be avoided. Port B is interoperable with all I2C-bus slaves, masters, and repeaters.
6.1 Enable
The EN pin is active HIGH and allows the user to select when the repeater is active. This can be used to isolate a badly behaved slave on power-up until after the system power-up reset. It should never change state during an I2C-bus operation because disabling during a bus operation will hang the bus and enabling part way through a bus cycle could confuse the I2C-bus parts being enabled. The enable pin should only change state when the bus and the repeater port are in an idle state to prevent system failures.
6.2 I2C-bus systems
As with the standard I2C-bus system, pull-up resistors are required to provide the logic HIGH levels on the buffered bus (standard open-collector configuration of the I2C-bus). The size of these pull-up resistors depends on the system. Each of the port A I/Os has an internal pull-up current source and does not require the external pull-up resistor. The port B is designed to work with Standard mode and Fast mode I2C-bus devices in addition to SMBus devices. Standard mode I2C-bus devices only specify 3 mA output drive; this limits the termination current to 3 mA in a generic I2C-bus system where Standard mode devices and multiple masters are possible. Under certain conditions higher termination currents can be used.
7. Application design-in information
A typical application is shown in Figure 4. In this example, the CPU is running on a 1.1 V I2C-bus while the master is connected to a 3.3 V bus. Both buses run at 400 kHz. Master devices can be placed on either bus.
1.1 V
3.3 V
10 k
10 k
VCC(A) SDA SCL 1.1 V CPU
10 k
VCC(B) B1 B2 SDA SCL MASTER 400 kHz
A1 A2
PCA9519
A8 EN B8
bus A
bus B
002aab642
Fig 4. Typical application
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
5 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
When port B of the PCA9519 is pulled LOW by a driver on the I2C-bus, a CMOS hysteresis detects the falling edge when it goes below 0.3VCC(B) and causes the internal driver on port A to turn on, causing port A to pull down to about 0.2 V. When port A of the PCA9519 falls, first a comparator detects the falling edge and causes the internal driver on port B to turn on and pull the port B pin down to ground. In order to illustrate what would be seen in a typical application, refer to Figure 5 and Figure 6. If the bus master in Figure 4 were to write to the slave through the PCA9519, waveforms shown in Figure 5 would be observed on the B bus. This looks like a normal I2C-bus transmission. On the port A bus of the PCA9519, the clock and data lines would have a positive offset from ground equal to the VOL of the PCA9519. After the 8th clock pulse, the data line will be pulled to the VOL of the master device, which is very close to ground in this example. At the end of the acknowledge, the level rises only to the LOW level set by the driver in the PCA9519 for a short delay while the port B bus rises above 0.5VCC(B), then it continues HIGH. It is important to note that any arbitration or clock stretching events require that the LOW level on the port A bus at the input of the PCA9519 (VIL) is below VILc to be recognized by the PCA9519 and then transmitted to the port B bus.
9th clock pulse acknowledge SCL
SDA
002aab644
Fig 5. Bus B SMBus/I2C-bus waveform
9th clock pulse acknowledge SCL
SDA VOL of PCA9519
002aab645
VOL of master
Fig 6. Bus A lower voltage waveform
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
6 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
8. Limiting values
Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VCC(B) VCC(A) VI/O II/O II Ptot Tstg Tamb Tj Tsp Parameter supply voltage port B supply voltage port A voltage on an input/output pin input/output current input current total power dissipation storage temperature ambient temperature junction temperature solder point temperature 10 s max. operating in free air port A port B; enable pin (EN) Conditions Min -0.5 -0.5 -0.5 -0.5 -65 -40 Max +6 +6 +6 +6 20 20 100 +150 +85 125 300 Unit V V V V mA mA mW C C C C
9. Static characteristics
Table 4. Static characteristics GND = 0 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol Supplies VCC(B) VCC(A) ICC(A) ICC(B) VIH VIL VILc VIK ILI IIL VOL VOL-VILc ILOH Cio supply voltage port B supply voltage port A supply current port A supply current port B HIGH-level input voltage LOW-level input voltage contention LOW-level input voltage input clamping voltage input leakage current LOW-level input current LOW-level output voltage difference between LOW-level output and port A LOW-level input voltage contention HIGH-level output leakage current input/output capacitance VO = 1.1 V IL = -18 mA VI = VCC(A)
[3] [4] [5]
Parameter
Conditions
Min 3.0 1.0
Typ[1] 2.1 11.6 3.3 +0.15 -1 0.2 50 6
Max 5.5 VCC(B) - 1 3.6 20 4.5 VCC(A) +0.3 -0.5 1 -0.45 0.35 10 7
Unit V V mA mA mA V V V V A mA V mV A pF
all port A static HIGH all port A static LOW all port B static HIGH port A port A
[2] [2]
1 5 2 0.7VCC(A) -0.5 -0.5 -1.5 -1.5 -
Input and output of port A (A1 to A8)
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
7 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
Table 4. Static characteristics ...continued GND = 0 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol VIH VIL VIK ILI IIL VOL ILOH Cio Enable VIL VIH IIL(EN) ILI Ci
[1] [2] [3]
Parameter HIGH-level input voltage LOW-level input voltage input clamping voltage input leakage current LOW-level input current LOW-level output voltage HIGH-level output leakage current input/output capacitance LOW-level input voltage HIGH-level input voltage LOW-level input current on pin EN input leakage current input capacitance
Conditions
Min 0.7VCC(B) -0.5
Typ[1] 0.1 6 2
Max VCC(B) -0.5 +1.0 10 0.2 10 7 0.1VCC(A) VCC(B) +1 +1 3
Unit V V A A V A pF V V A A pF
Input and output of port B (B1 to B8) +0.3VCC(B) V
IL = -18 mA VI = 3.6 V VI = 0.2 V IOL = 6 mA VO = 3.6 V
-1.5 -1.0 -0.5 0.9VCC(A)
VI = 0.2 V, EN; VCC = 3.6 V VI = 3.0 V or 0 V
-1 -1 -
Typical values with VCC(A) = 1.1 V, VCC(B) = 5.0 V. VIL specification is for the falling edge seen by the port A input. VILc is for the static LOW levels seen by the port A input resulting in port B output staying LOW. The port A current source has a typical value of about 1 mA, but varies with both VCC(A) and VCC(B). Below VCC(A) of about 0.7 V the port A current source current drops to 0 mA. The current source current dropping across the internal pull-down driver resistance of about 200 defines the VOL. As long as the chip ground is common with the input ground reference the driver resistance may be as large as 120 . However, ground offset will rapidly decrease the maximum allowed driver resistance. Guaranteed by design.
[4] [5]
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
8 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
10. Dynamic characteristics
Table 5. Symbol tPLH tPHL tTLH tTHL tPLH tPLH2 Dynamic characteristics Parameter LOW-to-HIGH propagation delay HIGH-to-LOW propagation delay LOW to HIGH output transition time HIGH to LOW output transition time LOW-to-HIGH propagation delay LOW to HIGH propagation delay 2 Conditions port B to port A port B to port A port A port A port A to port B port A to port B; measured from the 50 % of initial LOW on port A to 1.5 V rising on port B port A to port B port B port B EN HIGH before START condition EN HIGH after STOP condition port B to port A port B to port A port A port A port A to port B port A to port B; measured from the 50 % of initial LOW on port A to 1.5 V rising on port B port A to port B port B port B EN HIGH before START condition EN HIGH after STOP condition
[1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1]
Min 69 63 14 5 -69 91
Typ 109 86 22 8.1 -91 153
Max 216 140 96 16 -139 226
Unit ns ns ns ns ns ns
VCC(A) = 1.1 V; VCC(B) = 3.3 V
tPHL tTLH tTHL tsu th tPLH tPHL tTLH tTHL tPLH tPLH2
HIGH-to-LOW propagation delay LOW to HIGH output transition time HIGH to LOW output transition time setup time hold time LOW-to-HIGH propagation delay HIGH-to-LOW propagation delay LOW to HIGH output transition time HIGH to LOW output transition time LOW-to-HIGH propagation delay LOW to HIGH propagation delay 2
[1] [1][2] [1]
73 15 100 100 69 63 14 5 -69 91
122 61 24 105 86 27 8 -89 131
183 40 216 140 96 35 -139 226
ns ns ns ns ns ns ns ns ns ns ns
VCC(A) = 1.9 V; VCC(B) = 5.0 V
tPHL tTLH tTHL tsu th
[1] [2]
HIGH-to-LOW propagation delay LOW to HIGH output transition time HIGH to LOW output transition time setup time hold time
[1] [1][2] [1]
73 15 100 100
99 65 31 -
183 40 -
ns ns ns ns ns
Load capacitance = 50 pF; load resistance on port B = 1.35 k. Value is determined by RC time constant of bus line.
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
9 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
10.1 AC waveforms
VCC(B) input 0.5VCC(B) tPHL 70 % 0.5VCC(B) 0.1 V tPLH 70 % VCC(A) output VOL
002aab646
VCC(A) input 0.5VCC(A) tPHL 70 % 0.5VCC(A) tPLH 70 % tTLH
002aab647
VCC(B)
output
0.5VCC(A) 0.5VCC(A) 30 % 30 % tTHL
0.5VCC(B) 0.5VCC(B) 30 % 30 % tTHL
tTLH
Fig 7. Propagation delay and transition times; port B to port A
Fig 8. Propagation delay and transition times; port A to port B
input port A 50 % of initial value
output port B tPLH2
0.5VCC(B)
002aab648
Fig 9. Propagation delay from port A's external driver switching off to the port B LOW-to-HIGH transition; port A to port B
11. Test information
VCC(B) VCC(A) PULSE GENERATOR VI DUT
RT CL
VCC(B)
RL
VO
002aab649
RL = load resistor; 1.35 k on port B CL = load capacitance includes jig and probe capacitance; 50 pF RT = termination resistance should be equal to Zo of pulse generators
Fig 10. Test circuit for open-drain outputs
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
10 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
12. Package outline
TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1
D
E
A
X
c y HE vMA
Z
20
11
Q A2 pin 1 index A1 (A 3) A
Lp L
1
e bp
10
wM detail X
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 6.6 6.4 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.5 0.2 8 o 0
o
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT360-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19
Fig 11. Package outline SOT360-1 (TSSOP20)
PCA9519_1 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
11 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
HVQFN24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm
SOT616-1
D
B
A
terminal 1 index area A A1 E c
detail X
e1
1/2 e
C b 12 vMCAB wMC 13 e y1 C y
e 7 L 6
Eh
1/2 e
e2
1
18
terminal 1 index area
24 Dh 0
19 X 2.5 scale 5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. 1 A1 0.05 0.00 b 0.30 0.18 c 0.2 D (1) 4.1 3.9 Dh 2.25 1.95 E (1) 4.1 3.9 Eh 2.25 1.95 e 0.5 e1 2.5 e2 2.5 L 0.5 0.3 v 0.1 w 0.05 y 0.05 y1 0.1
Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. OUTLINE VERSION SOT616-1 REFERENCES IEC --JEDEC MO-220 JEITA --EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22
Fig 12. Package outline SOT616-1 (HVQFN24)
PCA9519_1 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
12 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
13. Soldering
13.1 Introduction to soldering surface mount packages
There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended.
13.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Driven by legislation and environmental forces the worldwide use of lead-free solder pastes is increasing. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 seconds and 200 seconds depending on heating method. Typical reflow temperatures range from 215 C to 260 C depending on solder paste material. The peak top-surface temperature of the packages should be kept below:
Table 6. SnPb eutectic process - package peak reflow temperatures (from J-STD-020C July 2004) Volume mm3 < 350 240 C + 0/-5 C 225 C + 0/-5 C Volume mm3 350 225 C + 0/-5 C 225 C + 0/-5 C
Package thickness < 2.5 mm 2.5 mm Table 7.
Pb-free process - package peak reflow temperatures (from J-STD-020C July 2004) Volume mm3 < 350 260 C + 0 C 260 C + 0 C 250 C + 0 C Volume mm3 350 to 2000 260 C + 0 C 250 C + 0 C 245 C + 0 C Volume mm3 > 2000 260 C + 0 C 245 C + 0 C 245 C + 0 C
Package thickness < 1.6 mm 1.6 mm to 2.5 mm 2.5 mm
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
13.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results:
* Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
* For packages with leads on two sides and a pitch (e):
PCA9519_1 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
13 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
- larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end.
* For packages with leads on four sides, the footprint must be placed at a 45 angle to
the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 C or 265 C, depending on solder material applied, SnPb or Pb-free respectively. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications.
13.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 seconds to 5 seconds between 270 C and 320 C.
13.5 Package related soldering information
Table 8. Package[1] BGA, HTSSON..T[3], LBGA, LFBGA, SQFP, SSOP..T[3], TFBGA, VFBGA, XSON DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP, HSQFP, HSSON, HTQFP, HTSSOP, HVQFN, HVSON, SMS PLCC[5], SO, SOJ LQFP, QFP, TQFP SSOP, TSSOP, VSO, VSSOP CWQCCN..L[8],
[1] [2]
Suitability of surface mount IC packages for wave and reflow soldering methods Soldering method Wave not suitable not suitable[4] Reflow[2] suitable suitable
suitable not not WQCCN..L[8] recommended[5][6] recommended[7]
suitable suitable suitable not suitable
PMFP[9],
not suitable
For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026); order a copy from your Philips Semiconductors sales office. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods.
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
14 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
[3]
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217 C 10 C measured in the atmosphere of the reflow oven. The package body peak temperature must be kept as low as possible. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. Hot bar soldering or manual soldering is suitable for PMFP packages.
[4]
[5] [6] [7] [8]
[9]
14. Abbreviations
Table 9. Acronym CDM CMOS CPU DUT ESD HBM I/O I2C-bus MM NMOS RC SMBus Abbreviations Description Charged Device Model Complementary Metal Oxide Semiconductor Central Processing Unit Device Under Test ElectroStatic Discharge Human Body Model Input/Output Inter-Integrated Circuit Bus Machine Model Negative-channel Metal Oxide Semiconductor Resistor Capacitor network System Management Bus
15. Revision history
Table 10. Revision history Release date 20060622 Data sheet status Objective data sheet Change notice Supersedes Document ID PCA9519_1
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
15 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
16. Legal information
16.1 Data sheet status
Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet
[1] [2] [3]
Product status[3] Development Qualification Production
Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification.
Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.semiconductors.philips.com.
16.2 Definitions
Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Philips Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Philips Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
to result in personal injury, death or severe property or environmental damage. Philips Semiconductors accepts no liability for inclusion and/or use of Philips Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- Philips Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.semiconductors.philips.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by Philips Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
16.3 Disclaimers
General -- Information in this document is believed to be accurate and reliable. However, Philips Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- Philips Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- Philips Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a Philips Semiconductors product can reasonably be expected
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of Koninklijke Philips Electronics N.V.
17. Contact information
For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
PCA9519_1
(c) Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Objective data sheet
Rev. 01 -- 22 June 2006
16 of 17
Philips Semiconductors
PCA9519
4-channel level translating I2C-bus/SMBus repeater
18. Contents
1 2 3 4 5 5.1 5.2 6 6.1 6.2 7 8 9 10 10.1 11 12 13 13.1 13.2 13.3 13.4 13.5 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 I2C-bus systems . . . . . . . . . . . . . . . . . . . . . . . . 5 Application design-in information . . . . . . . . . . 5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 7 Static characteristics. . . . . . . . . . . . . . . . . . . . . 7 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . 10 Test information . . . . . . . . . . . . . . . . . . . . . . . . 10 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Introduction to soldering surface mount packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 13 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 13 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 14 Package related soldering information . . . . . . 14 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 15 Legal information. . . . . . . . . . . . . . . . . . . . . . . 16 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 16 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Contact information. . . . . . . . . . . . . . . . . . . . . 16 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'.
(c) Koninklijke Philips Electronics N.V. 2006.
All rights reserved.
For more information, please visit: http://www.semiconductors.philips.com. For sales office addresses, email to: sales.addresses@www.semiconductors.philips.com. Date of release: 22 June 2006 Document identifier: PCA9519_1

▲Up To Search▲

Price & Availability of PCA9519

	To Download PCA9519 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .